archive-sg.com » SG » A » ALARMSUPPLY.COM.SG

Total: 60

Choose link from "Titles, links and description words view":

Or switch to "Titles and links view".
  • Alarm Supply Pte Ltd
    detector meets the requirements for a CS detector in EN54 5 2000 Part no 59000 405 with standard base Part no 55000 406 with LED driver base back to apollo menu Apollo XPlorer Isolator General Introduction The XPlorer isolator senses and isolates short circuit faults on XPlorer loops It is loop powered and polarity sensitive Power and signals to the affected section are restored automatically when the fault is cleared Part no 59000 700 back to apollo menu Apollo XPlorer Manual Call Point MCP General Introduction The XPlorer manual call point is designed for surface mounting and incorporates the call point assembly and a black box The address of each call point is set at the commissioning stage by means of a six segment DIL switch giving a range of addresses from 64 to 126 A single alarm LED provided on the call point This LED is controlled independently of the call point by the CIE Call points can be remotely tested from the control and indicating equipment by transmission of a single bit in the communications protocol Call points responds by providing a value of 64 which corresponds to the alarm value The CIE will recognise this response as a test signal and will not raise a general alarm back to apollo menu Apollo XPlorer Optical Smoke Detector General Introduction The XPlorer optical detector has a moulded self extinguishing white polycarbonate case designed to allow free entry of smoke while minimising the effects of dust contamination Stainless steel wiper contacts connect the monitor to the terminals in the mounting base Within the case is a printed circuit board which on one side has the lightproof labyrinth chamber with integral gauze surrounding the optical measuring system The other side has the address capture signal processing and communications electronics An infrared

    Original URL path: http://www.alarmsupply.com.sg/pro_apo_xplorer.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    converted to a digital signal by the electronic circuitry and transmitted to the control equipment on interrogation The microprocessor in the control equipment then compares the signal with stored data and initiates a pre alarm or fire alarm as smoke density increases When the equipment determines that a fire condition exists it instructs the monitor to switch on its indicator LED and the pre planned alarm routine is initiated back to apollo menu Apollo XP95 Isolator General Introduction Isolators are designed to protect the XP95 loop in the event of a short circuit fault They divide a loop of fire monitors and ancillary devices into groups of 20 as a rule so that in the event of a short circuit no more than 20 devices will be inoperable The XP95 isolator has particularly low non isolating resistance back to apollo menu Apollo XP95 Manual Call Point MCP General Introduction When activated the XP95 manual call point not only interrupts the polling cycle to indicate to the control panel that it has been operated but also reports its address Thus an alarm and its location can be reported in less than 0 2 seconds back to apollo menu Apollo XP95 Optical Smoke Detector General Introduction The XP95 optical smoke monitor uses the same optical arrangement as the Series 60 optical smoke detector with an internal pulsing LED and a photo diode at an obtuse angle In clear air conditions the photo diode in the XP95 monitor receives no light from the LED and produces a corresponding analogue signal This signal increases when smoke enters the chamber and light is scattered onto the photo diode The signal is processed by the electronic circuitry and transmitted to the control equipment in exactly the same way as in the case of the ionisation smoke

    Original URL path: http://www.alarmsupply.com.sg/pro_apo_xp95.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    to face the same way there is a guide mark on the base that allows correct positioning All bases have a mechanism for locking detectors if required Also available is a diode base for use in systems which continue to operate even if one or more detectors have been removed without authorisation and a relay base back to apollo menu Apollo Orbis Heat Detector General Introduction Orbis heat detectors are suitable in atmospheres with high dust content or where fumes may temporarily be concentrated such as vehicles loading bays The heat detectors have an open web casing that allows air to flow freely acrossly a thermistor which measures the air temperature every 2 seconds The stored temperatures are then compared against pre set values to determine whether an alarm level has been reached There are six heat detectors to suit a wide variety of operating conditions Static heat detectors respond only when a fixed temperature has been reached Rate of rise detectors have a fixed upper limit too but they also measure the rate of increase in temperature back to apollo menu Apollo Orbis Multisensor Smoke Detector General Introduction The multisensor smoke detector is a thermally enhanced smoke detector that is a development of the optical detector and goes even further in its capabilities of fire detection The optical sensor is influenced by the heat sensing element making the detector more responsive to fast burning flaming fires It should be used as the detector of choice in areas of high risk with heat at an early stage of the conflagration and with increased likelihood of unwanted alarms back to apollo menu Apollo Orbis Optical Smoke Detector General Introduction The Orbis optical smoke detector s sensing technology makes it significantly different in design from existing optical detectors Although the Orbis optical

    Original URL path: http://www.alarmsupply.com.sg/pro_apo_orbis.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    large termination area Dual M20 ISO cable gland entries supplied with one stopping plug Ratchet adjustable stainless steel U bracket for positive adjustment under harsh conditions IN OUT terminals Terminals accept 0 5 to 4 0mm 2 cables Line monitoring Min 500 Ohm 2w or 3k3 Ohm 0 5w resistor or diode within EExd enclosure dc versions The beacons may be connected from a single supply for simultaneous operation or from seperate supplies for independent operation back to e2s menu E2S BExBG05D E ATEX EEx 5 Joule Hazardous Area Xenon Warning Beacons General Introduction 5 Joule Xenon 1Hz 60 FPM 5 Ws BExBG05D EEx d IIC T5 Tamb 50 to 55 C EEx d IIC T6 Tamb 50 to 40 C BExBG05E EEx de IIC T5 Tamb 50 to 55 C EEx de IIC T6 Tamb 50 to 40 C KEMA certified ATEX CENELEC FTZU approved Suitable for Zone 1 2 21 22 Gas Groups IIC IIB IIA Voltages 12vdc 24vdc 48vdc 115vac 230vac Six lens colours available Amber Blue Clear Green Red Yellow Automatic synchronisation on multi beacon systems Beacons can be set to flip flop alternating mode with other units on multi beacon systems Tube life emissions reduced to 70 after 8 million flashes Xenon tubes mechanically secured against shock vibration BExCBG05D IP67 BExBG05E IP66 Enclosure material Marine grade LM6 Aluminium Chromated powder coated finish good resistance to humidity and salt spray environments Glass lens Stainless Steel guard Colour available Red RAL3000 Operating temperature 50 to 55 C 50 to 40 C Storage temperature 50 to 70 C Large range of certified end of line resistors Weight DC 2 45Kg AC 2 75Kg KEMA Certificate number 00ATEX2006 X Installation Features Very large termination area Dual M20 ISO cable gland entries supplied with one stopping plug Ratchet adjustable stainless steel U bracket for positive adjustment under harsh conditions IN OUT terminals Terminals accept 0 5 to 4 0mm 2 cables Line monitoring Min 500 Ohm 2w or 3k3 Ohm 0 5w resistor or diode within EExd enclosure dc versions back to e2s menu E2S BExBG10D E ATEX EEx 10 Joule Hazardous Area Xenon Warning Beacons General Introduction 10 Joule Xenon 1Hz 60 FPM 10 Ws BExBG10D EEx d IIC T4 Tamb 50 to 55 C EEx d IIC T5 Tamb 50 to 40 C BExBG10E EEx de IIC T4 Tamb 50 to 55 C EEx de IIC T5 Tamb 50 to 40 C KEMA certified ATEX CENELEC FTZU approved Suitable for Zone 1 2 21 22 Gas Groups IIC IIB IIA Voltages 12vdc 24vdc 48vdc 115vac 230vac Six lens colours available Amber Blue Clear Green Red Yellow Automatic synchronisation on multi beacon systems Beacons can be set to flip flop alternating mode with other units on multi beacon systems Tube life emissions reduced to 70 after 8 million flashes Xenon tubes mechanically secured against shock vibration BExCBG10D IP67 BExBG10E IP66 Enclosure material Marine grade LM6 Aluminium Chromated powder coated finish good resistance to humidity and salt spray environments Glass

    Original URL path: http://www.alarmsupply.com.sg/pro_e2s_beacons.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    at 20 C Weight DC 2 50Kg AC 3 00Kg Beacon 5 Joule 1Hz 5 Ws Automatic synchronised flash or Flip Flop alternating mode 6 lens colours available Xenon tube mechanically secured against vibration shock Large termination area 2 x M20 ISO Cable gland entries with 1 blanking plug Ratchet adjustable stainless steel U bracket for 360 positioning All units offer IN and OUT terminals Terminals accept 0 5 to 4 0mm 2 cables Sounder beacon may use same supply for simultaneous operation or seperate supplies for independent operation back to e2s menu E2S MCL15 05 Marine Grade IP67 15w Loudspeaker Xenon Beacon General Introduction A heavy duty high output IP67 sealed loudspeaker beacon ideal for harsh environments with high ambient noise levels also requiring a visual indicator Third party tested to IP67 IP66 Enclosure material UL94V0 5VA rated FR ABS Colour available Grey RAL7038 Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight 70 100v line 2 60Kg Low inpedance 2 20Kg Large termination area 2 x M20 ISO Cable gland entries with 1 blanking plug Ratchet adjustable stainless steel U bracket for 360 positioning All units offer IN and OUT terminals Terminals accept 0 5 to 4 0mm 2 cables Loudspeaker SPL 108dB 3dB 1w 1m Pink noise 118dB 3dB 15w Rated Power 1m Rated power 15 Watts RMS 70v line transformer version 25w 12 5w 6w 2w tappings z 196 Ohms 392 Ohms 816 67 Ohms 2 45k Ohms 100v line transformer version 25w 12 5w 6w 2w tappings z 400 Ohms 800 Ohms 1 67k Ohms 5k Ohms Impedance type 8 Ohm or 16 Ohm Dispersion 120 1kHz 32 4kHz Frequency range 400Hz to 8000Hz DC line monitoring 2 2uF Capacitor Transformer type speaker 470uF Capacitor Impedance type speaker Transformer type fitted with thermal fuse Complies with BS5839 part 8 Beacon Beacon 5 Joule 1Hz 5 Ws Automatic synchronised flash or Flip Flop alternating mode 6 lens colours available Beacon voltage 12vdc 24vdc 48vdc 115vac 230vac DC versions have reverse polarity protection Xenon tube mechanically secured against vibration shock back to e2s menu E2S BExCA110 05D BExDCA110 05D ATEX EEx Combined Voice Sounder Beacon General Introduction The sounder records stores and plays back user defined messages stored directly to non volatile memory without any intermediate analogue to digital conversion A single 16 second message may be recorded and played back with a choice of 1 of 10 user selectable alarm tones including silence to allow speech only CA110 05D EEx d IIB T4 Tamb 50 to 55 C KEMA certified ATEX CENELEC approved Voltages 24vdc 115vac 230vac CA110 05D IP67 Enclosure material Marine grade LM6 Aluminium Chromated powder coated finish good resistance to humidity and salt spray environments BExCA110 05D Horn High impact UL94 V0 5VA FR ABS BExDCA110 05D Horn Anti Static High impact ABS Colour available Red RAL3000 Operating temperature 50 to 55 C Storage temperature 50 to 70 C Large range of certified

    Original URL path: http://www.alarmsupply.com.sg/pro_e2s_combinations.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    third party tested copy of report available on request Installation Features Very large termination area Dual M20 ISO cable gland entries supplied with one stopping plug Ratchet adjustable stainless steel U bracket for positive adjustment under harsh conditions IN OUT terminals Terminals accept 0 5 to 4 0mm 2 cables back to e2s menu E2S BExL25 BExDL25 ATEX EEx 25 Watt Hazardous Area Loudspeakers General Introduction SPL 105dB 3dB 1w 1m Pink noise 117dB 3dB 25w Rated Power 1m L25D EEx d IIC T4 Tamb 50 to 55 C L25E EEx de IIC T4 Tamb 50 to 55 C KEMA certified ATEX CENELEC FTZU approved Suitable for Zone 1 2 Gas groups IIC IIB IIA Rated power 25 Watts RMS 70v line transformer version 25w 12 5w 6w 2w tappings z 196 Ohms 392 Ohms 816 67 Ohms 2 45k Ohms 100v line transformer version 25w 12 5w 6w 2w tappings z 400 Ohms 800 Ohms 1 67k Ohms 5k Ohms Impedance type 8 Ohm or 16 Ohm Dispersion 130 1kHz 32 4kHz Frequency range 300Hz to 8000Hz DC line monitoring 2 2uF Capacitor Transformer version 470uF Capacitor Impedance version L25D IP67 L25E IP66 Enclosure material Marine grade LM6 Aluminium Chromated powder coated finish good resistance to humidity and salt spray environments BExL25 Horn High impact UL94 V0 5VA FR ABS BExDL25 Horn Anti static High impact ABS Colour available Red RAL3000 Operating temperature 50 to 50 C Storage temperature 50 to 70 C Weight 70 100v line 3 95Kg Low impedance 3 56Kg KEMA Certificate number 99ATEX6312 Loudspeaker third party tested copy of report available on request Installation Features Very large termination area Dual M20 ISO cable gland entries supplied with one stopping plug Ratchet adjustable stainless steel U bracket for positive adjustment under harsh conditions IN OUT terminals Terminals accept 0 5 to 4 0mm 2 cables back to e2s menu E2S ML15 Marine Grade IP67 15 Watt Loudspeaker General Introduction A heavy duty high output IP67 sealed loudspeaker ideal for harsh environments with high ambient noise levels SPL 108dB 3dB 1w 1m Pink noise 118dB 3dB 15w Rated Power 1m Rated power 15 Watts RMS 70v line transformer version 15w 7 5w 3w 1w tappings z 336 67 Ohms 653 33 Ohms 1 6k Ohms 4 9k Ohms 100v line transformer version 15w 7 5w 3w 1w tappings z 666 87 Ohms 1 34k Ohms 3 34k Ohms 10k Ohms Impedance type 8 Ohm or 16 Ohm Dispersion 120 1kHz 32 4kHz Frequency range 400Hz to 8000Hz DC line monitoring 2 2uF Capacitor Transformer type speaker 470uF Capacitor Impedance type speaker Transformer type fitted with thermal fuse Complies with BS5839 part 8 Third party tested to IP67 IP66 Enclosure material UL94V0 5VA rated FR ABS Colour available Grey RAL7038 Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight 70 100v line 2 60Kg Low impedance 2 20Kg Large termination area 2 x M20 ISO cable gland entries

    Original URL path: http://www.alarmsupply.com.sg/pro_e2s_loudspeakers.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    Approved Standard 3610 Entity Code CLI II III Div 1 GPA B C D E F G Installation The A105N IS B A105N IS C may be powered from any certified Zener barrier whose output parameters do not exceed Uo 30VDC lo 110mADC Wo 0 85W or from any galvanic isolator specified by the system certificates Terminals accept 0 5 to 2 5mm 2 cables Current 25mA typical when powered from 24v supply via 28v 300 Ohm Zener barrier Second Third stage alarms 2nd Stage Less than 0 9v 3rd Stage Less than 0 9v back to e2s menu E2S A112 AL112 AlertAlarm Alarm Sounder General Introduction A very high output sounder ideal for industrial applications with high ambient noise levels Maximum output 119dB A 1 metre Nominal output 112dB A 1m 3dB Tone 2 45 alarm tones 3 stage alarm option Volume control Automatic synchronisation on multi sounder systems 125m effective range 1kHz Voltages 24vdc 10 30vdc 48vdc 35 60vdc 24vac 115vac 230vac Other voltages available upon request DC versions may be used on 24vac 10 for single stage applications Positive stage switching DC version available Reverse polarity switching on DC units Fully programmable version with 4 stage available IP55 can be increased to IP56 dust protected watertight with WR kit Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 Grey or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight A112 DC 1 80Kg AC 2 10Kg AL112 DC 2 00Kg AC 2 30Kg UL approved version available Large termination area Cable gland knockouts in the rear of the unit Side M20 cable gland entry and IP55 stopping plug Unit can be mounted using external lugs or internal BESA compatible fixing positions All units offer IN and OUT terminals Terminals accept 0 5 to 4 0mm 2 cables back to e2s menu E2S A121 AL121 AlertAlarm Alarm Sounder General Introduction A very high output sounder ideal for industrial applications with high ambient noise levels Maximum output 126dB A 1 metre Nominal output 121dB A 1m 3dB Tone 2 45 alarm tones UKOOA PFEER compliant 3 stage alarm option Volume control Automatic synchronisation on multi sounder systems 300m effective range 1kHz Voltages 24vdc 10 30vdc 48vdc 35 60vdc 24vac 115vac 230vac Other voltages available upon request DC versions may be used on 24vac 10 for single stage applications Positive stage switching DC version available Reverse polarity switching on DC units Fully programmable version with 4 stage available IP55 can be increased to IP56 dust protected watertight with WR kit Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 Grey or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight A121 DC 2 10Kg AC 2 70Kg AL121 DC 2 30Kg AC 2 90Kg UL approved version available Large termination area Cable gland knockouts in the rear of the unit Side M20 cable gland entry and IP55 stopping plug Unit can be mounted using external lugs or internal BESA compatible fixing positions All units offer IN and OUT terminals Terminals accept 0 5 to 4 0mm 2 cables back to e2s menu E2S Bedhead Flush Mount Alarm Sounder General Introduction Maximum output 95dB A 1 metre Nominal output 90dB A 1m 3dB 10 alarm tones 3 stage alarm option Volume control 10m effective range 1kHz Voltage 24vdc 10 30vdc Tropicalisation available on request Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight 0 06Kg Compatible with standard BESA back boxes All units offer IN and OUT terminals Terminals accept 0 5 to 2 5mm 2 cables back to e2s menu E2S SON2 Sonora Alarm Sounder General Introduction A continuously rated compact sounder ideal for fire and security applications Maximum output 104dB A 1 metre Nominal output 100dB A 1m 3dB Tone 2 32 alarm tones 3 stage alarm option Volume control 3 levels Automatic synchronisation on multi sounder systems 32m effective range 1kHz Voltages 24vdc 10 30vdc 115vac 230vac Other voltages available upon request Reverse polarity switching on DC units Reverse polarity diode protection on DC units IP55 can be increased to IP56 dust protected watertight with WR kit Tropicalisation available on request Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 Grey or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight DC 0 30Kg AC 0 40Kg 4 x gland knockouts in side back Mounting via internal BESA compatible fixing positions AC units have external mounting lugs in addition to the above All units offer IN and OUT terminals Terminals accept 0 5 to 2 5mm 2 cables back to e2s menu E2S SONF1 SONFL1 Sonora Alarm Sounder General Introduction A continuously rated compact sounder ideal for fire and security applications Nominal output 100dB A 1m 3dB Tone 2 10 alarm tones 2 stage alarm option Volume control Automatic synchronisation on multi sounder systems 32m effective range 1kHz Voltages 24vdc 10 30vdc Other voltages available upon request Reverse polarity diode protection on DC units IP55 can be increased to IP56 dust protected watertight with WR kit Tropicalisation available on request Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight 0 26Kg UL approved version available 4 x gland knockouts in side back Mounting via internal BESA compatible fixing positions All units offer IN and OUT terminals Terminals accept 0 5 to 2 5mm 2 cables back to e2s menu E2S BExS110 BExDS110 ATEX EEx Hazardous Area Alarm Sounders General Introduction Maximum output 117dB A 1 metre Nominal output 110dB A 1m 3dB Tone 2 S110D EEx d IIC T4 Tamb 50 to 55

    Original URL path: http://www.alarmsupply.com.sg/pro_e2s_sounders.html (2012-12-22)
    Open archived version from archive

  • Alarm Supply Pte Ltd
    and OUT terminals Terminals accept 0 5 to 4 0mm 2 cables Line monitoring Min 500 Ohm 2w 3k3 Ohm 0 5w resistor or diode within EExd enclosure dc versions back to e2s menu E2S MV112 Marine Grade IP67 Voice Annunciation Unit General Introduction A heavy duty high output IP67 sealed voice annunciation sounder ideal for harsh environments with high ambient The sounder records stores and plays back user defined messages stored directly to non volatile memory without any intermediate analogue to digital conversion A single 16 second or two 8 second messages may be recorded and played back with a choice of 1 of 10 user selectable alarm tones Maximum output 110dB A 1 metre Voice output approx 105dB A 1m 3dB Direct message storage on silicon 16 seconds of speech Very high voice reproduction quality moving coil loudspeaker 10 alarm tones including silence to allow speech only option UKOOA PFEER compliant Volume control tone duration control Message length 1 x 16 seconds or 2 x 8 seconds 100m effective range 1kHz Voltages 12vdc 9 15vdc 24vdc 18 30vdc 115vac 230vac Easy message creation with built in microphone Edits automatically to message length Third party tested to IP67 IP66 Enclosure material UL94V0 5VA rated FR ABS Colour available Grey RAL7038 Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight DC 2 50Kg AC 3 00Kg Large termination area 2 x M20 ISO cable gland entries with 1 blanking plug Ratchet adjustable stainless steel U bracket for 360 positioning Terminals accept 0 5 to 4 0mm 2 cables back to e2s menu E2S A105N Appello P I R Voice Annunciation Unit General Introduction Record store a user defined 16 second voice message Message is repeated whilst P I R remains activated Maximum output 105dB A 1 metre Direct message storage on silicon 16 seconds of speech Very high voice reproduction quality moving coil loudspeaker Volume control P I R is in constant monitoring state replays message upon activation 32m effective range 1kHz Voltages 12vdc 9 15vdc 24vdc 18 30vdc 115vac 230vac Easy message creation with built in microphone Edits automatically to message length DC versions have reverse polarity diode protection IP55 can be increased to IP66 dust protected watertight with WR kit Tropicalisation available on request Enclosure material UL94V0 5VA rated FR ABS Colour available Red RAL3000 Grey or White Operating temperature 25 to 55 C Storage temperature 40 to 70 C Relative humidity 90 at 20 C Weight DC 0 75Kg AC 1 10Kg Cable gland knockouts in the rear of the unit Side M20 cable gland entry and IP55 stopping plug Unit can be mounted using external lugs or internal BESA compatible fixing positions All units offer IN and OUT terminals Terminals accept 0 5 to 2 5mm 2 cables back to e2s menu E2S A105N Appello Speech Tone Voice Annunciation Unit General Introduction The sounder records stores and plays back user defined messages stored directly to non

    Original URL path: http://www.alarmsupply.com.sg/pro_e2s_annunciators.html (2012-12-22)
    Open archived version from archive